- This topic is empty.
-
Posts
-
Good morning, I have a QK-A032, with and electronic raymarine nmea200, and a gps garmin connected byQK-As03 protocol bridge.
The problem it´s, when i start everithing and connect, all it´s fine, the gps refresh at very late, 2seconds, 20 seconds, 14 seconds,40 seconds, has nos a rule, and when pass 10 minutes, the information of electronic it´s lock and no run, and the gps starts run fine.
What do you think is happening?
Regards
Alejandro
Sorry for the problem you have. Which A032 version you have, standard or AIS version? If you are using standard one you can download the latest firmware from:
https://www.quark-elec.com/doc/A032_V1.00.191107_97C2.zip” class=”bbcode_url”>https://www.quark-elec.com/doc/A032_V1.00.191107_97C2.zipOtherwise, please contact us the get the new firmware for A032-AIS.
Hello,
I have the QK A032 standard. I updated the firmware and the nmea 2000, the light and the connection run well, but nmea 0183, the green led it´s out and no connection on the wifi.
Regards
Alejandro
Hi Alejandro,
More details please, e.g, what has been connected on NMEA 0183 port and what is the baud rate you have set up.
For the WiFi, make sure WiFi you haven’t set it to be standby(check this through configuration tool).
Keep us updated, please. Thanks.
Hello,
Finally I decide remove the GPS because run very bad, and disconnect the 0183 gate, and I buy a active gps antenna for raymarine and work all in nmea2000. In electrónic i have, position, sog and cog. But in my tablet only arrives position. The cog, sog, acuarity its 0. This data are lost.
Have a solución?
Regards
Alejandro
Hi Alex,
Can you check the firmware version of your A032 for us, please. You should be able to see it via the configuration tool.
Hello,
I upgrade the firmware to the last actualization .
Could be a baudio problem?
But i don understand because the posición ruin perfect, but cog,son and accuarici it,s 0.
What do you think?
Alex, since you have had the proper position I believe the data were converted properly.
Just remind you, there are a few NMEA 0183 sentences related to position/speed and angle. To investigate the issue you have, can you please provide a short log of the messages(NMEA 0183 format sentences) came from your GPS device, so we can go through with it.
Hello,
the firmware version it´s V1.00.191107.
Actually i have active gps antena raymarine and i70, but not a plotter. In the i70 SOG,position and COG run pefectly, but when i try to put this data in wifi for the tablet i only can see the position. COG and SOG not apear.
Can you please use the following link as the configuration tool to setup the WiFi output in NMEA 0183 format(you can choose from PCDIN and NMEA 0183 format) and send us a short log of the data which output from WiFi(you can also save the output from USB port since both are the same.
https://www.quark-elec.com/doc/A032_config_tool_161019.zip” class=”bbcode_url”>https://www.quark-elec.com/doc/A032_config_tool_161019.zipThank you.
Hello,
I connect by usb and use the pcdin. I have the same problem in the navegation program in the computer. I put all diferents combinations and nothing change.
SOG, COG and acuarity no run.
I put a new plotter and the resul it´s similar.
With the garmin and QK-Ao3 protocol bridge, the cog,sog and position appair but no refresh and with the raymarine position run perfect but not COG, SOG.
What do you think, could need any conversor?
Thank you.
Hello,
I have downloaded the program and connected, everything is fine but I don’t know how to extract the wifi output log. Is there any option or place to look?
Regards
Alejandro
There are many Apps can be used to monitor the WiFi(TCP/IP protocol) data. If you are using Android, you can use, netassist which we are using here. Contact us if you canot find it online. Thanks
Hello,
finally i could connect the PC and i have file with the sentence.
To remind you of the problem, gps position, sog and cog not run and in the plotter runs perfect. Y have a new electronic Raymarine with n2k. The firmware it´s in the last version.
The log it´s very very long I put only the first part and if you nedd more i can send you the full text.
¡¾Receive from 192.168.1.100 :2000¡¿£º
$IIMTW,21.70,C*27
$IIVHW,,T,71.19,M,,N,,K*75
$IIVHW,,T,71.65,M,,N,,K*7E
$IIVHW,,T,71.23,M,,N,,K*7C
$IIVHW,,T,71.38,M,,N,,K*76
$IIRSA,,V,-57295779513.08,A*6E
$WIMWV,192.46,R,11.49,N,A*16
$IIRSA,,V,-57295779513.08,A*6E
$TIROT,-11.68,A*18
$PCDIN,01F10D,00042975,AC,FCF8FF7FFF7FFFFF*26
$IIRSA,,V,-57295779513.08,A*6E
$WIMWV,192.46,R,11.49,N,A*16
$WIMWV,180.46,R,8.59,N,A*2C
$PCDIN,01F112,00042975,CC,FFB230FF7FFF7FFD*59
$IIVHW,,T,71.42,M,,N,,K*7B
$TIROT,-9.34,A*28
$IIVHW,,T,71.59,M,,N,,K*71
$IIRSA,,V,-57295779513.08,A*6E
$WIMWV,195.46,R,11.59,N,A*10
$WIMWV,197.96,R,10.79,N,A*1C
$IIVHW,,T,71.75,M,,N,,K*7F
$PCDIN,01FD02,00042975,69,0054024285FAFFFF*5C
$IIVHW,,T,71.18,M,,N,,K*74
$PCDIN,01F10D,00042975,AC,FCF8FF7FFF7FFFFF*26
$PCDIN,01F801,00042975,82,070CDA1699E6B5FF*5B
$IIVHW,,T,71.77,M,,N,,K*7D
$TIROT,7.01,A*0D
$PCDIN,01FD02,00042975,69,0054024285FAFFFF*5C
$GPDTM,EURD,,0000.0707,N,00000.0739,E,0.00,W84*3F
$WIMWV,180.46,R,8.59,N,A*2C
$WIMWV,190.46,R,12.29,N,A*11
$IIMTW,21.70,C*27
$IIVHW,,T,71.33,M,,N,,K*7D
$GPGLL,3820.3321,N,00029.1370,W,,A,A*51
$WIMWV,195.46,R,11.59,N,A*10
$WIMWV,197.96,R,11.68,N,A*1D
$PCDIN,01F112,00042973,CC,FFC430FF7FFF7FFD*58
$PCDIN,01F119,00042973,CC,FFC43048013B00FF*2D
$IIVHW,,T,71.82,M,,N,,K*77
$WIMWV,197.96,R,10.79,N,A*1C
$IIRSA,,V,-57295779513.08,A*6E
$WIMWV,197.96,R,11.68,N,A*1D
$PCDIN,01F112,00042973,CC,FFCC30FF7FFF7FFD*2F
$TIROT,-16.92,A*1A
$PCDIN,01F10D,00042973,AC,FCF8FF7FFF7FFFFF*20
Regards
Alejandro
Hello,
when i go to download the last version of the firmware QK A032S the file say “A032_V1.10.200425_CEFC” in this direction:
https://www.quark-elec.com/downloads/drivers/
is this the correct file?.
Thank you
Alejandro
Yes, I can confirm A032_V1.10.200425_CEFC is the latest firmware version(by 4 May 2020).
Did you mean the log which you posted was based on this new firmware? Thanks.
Hello,
finally everithing run fine. I have see the problem, when I dowloaded the last version of firmware, i was do it from tihs direction:
https://www.quark-elec.com/product/qk-a032-nmea-2000-0183-bi-directional-gateway/
and this is not the last version.
Thank you..
Alejandro
- You must be logged in to reply to this topic.